De Beltwinder is een op maat gemaakte machine maakt het vervangen van zware transportbanden (tot 27 ton) veilig en efficiënt. Met een krachtige aandrijving, hydraulisch verstelbare stuurrol en uitgebreide veiligheidsvoorzieningen...
This rectangular lifting frame was developed by our engineers for lifting a coldbox with a maximum weight of 14,000 kg.
The classifier for one of our clients was previously transported, stored, and set up using a wide range of tools and transport methods, which was cumbersome and risky. At Caden,...
In collaboration with a client specializing in technology for seal integrity inspection of food packaging, we developed a sealing detection machine capable of inspecting approximately 200 packages per minute. This...
Our client wanted to extend the chassis of an existing excavator to accommodate a hydrogen unit, enabling the excavator to operate on hydrogen. To accurately position this unit, they needed...
For this project, it was necessary to measure the entire interior of a delivery van to install custom-made interior linings accurately. A 3D scan is an ideal tool for measuring...
Hydraulic Ram Trailer is a company that builds ram trailers equipped with a patented push-out system. This system allows the trailers to unload their cargo in a stable, quick, and...
Sec-Construction specializes in building Racing Service Semi-Trailers, motorhomes, horse trailers, campers, and special vehicles. At the start of the 'World Rally Championship,' Toyota requested their assistance in creating a new...
Installing a 26-ton escalator in a hard-to-reach location where ground pressures must be kept to a minimum was a challenge that Caden tackled together with De Groote. Caden devised a...
Anders Beton approached Caden due to a shortage in their drawing capacity. They were looking for a partner to handle the engineering of a concrete mold.
Anders Beton's engineering department...
What if newly produced form plates break down much faster than the originals? That was the situation one of our clients encountered. Since their previous supplier of these plates had...
In a previous project, we developed a new type of spray nozzles for aerosol cans. Lacking a machine for this purpose, selections were previously made manually to have these nozzles...
A client in the pharmaceutical sector from Puurs needed to install a new HVAC system on the roof of one of their buildings. Since they required a steel support structure...
As a producer, you would prefer to avoid a pergola that fails under strong winds. For a pergola manufacturer, we conducted a wind simulation to investigate how the pergola behaves...
For a client in the pharmaceutical industry, we took on the complete development of a mobile research setup designed to test the surface of anodized aluminum trays for wear. The...
The focus of this project was the development of a swivel chair designed to facilitate the 180° tilting of a roll weighing 11 or 13 tons, with or without a...
For the removal and installation of dump nozzle caps on new ExxonMobil reactors, an innovative lifting tool was developed for our client HCI.
Together with a client from the nuclear sector, we developed an adapter for a vacuum cleaner for use underwater. This vacuum cleaner is used to suction up stainless steel chips...
Developing a tool to place a gearbox weighing over 400 kg onto a milling machine and rotate it 90° with just one finger—that was the challenging task Caden enthusiastically accepted...
Our client was facing issues with their existing pallet shuttles, which were not functioning properly. This resulted in frequent manual handling, which was very time-consuming. The goal of this project...
A few years ago, we developed a lifting cover that allowed our client to safely and easily lift a 6-meter-long heat exchanger with a diameter of 1.4 meters vertically. After...
Although reverse engineering projects are not uncommon for us, reverse engineering a gun turret from a First World War fort is less routine. Our client is an architectural firm specializing...
For Rombit, Caden developed a charger rack to efficiently charge their safety wearables.
For our pharmaceutical client in Puurs, we developed a manipulation tool that allows them to safely and efficiently remove their horizontal pistons for maintenance.
What if you want to automate the filling of containers to a specific weight? That was the goal of the project for one of our clients in the petrochemical industry...
For this project with ArcelorMittal, a gas pipe with a large diameter needed to be relocated. A 34-hour shutdown was planned during which the setup, execution, and dismantling of the...
FRC developed Greenspray, a spray system where the propellant is non-harmful. The challenge they faced was maintaining a consistent spray, which is a crucial factor.
Caden developed a spray system...
The safety hatch is used for safe descent via the existing ladder. It also serves as a secure barrier for the opening in the floor, both when open and...
